Main Page | Report this Page
 
Loading..
   
Science Forum Index  »  Electronics - Design Forum  »  Xilinx Coolrunner II CPLD power-down input characteristics?
Page 1 of 1    
Author Message
Spehro Pefhany
Posted: Sun Feb 25, 2007 12:30 pm
Guest
Hi, all:-

A bit of a long shot here, but does anyone know whether the inputs
will float on the Xilinx CPLD parts will float when power is not
applied or do they have a nasty protection structure to a supply pin?

And if so, what if I float the related Vccio pin-- will that allow the
input current to be reduced to just leakage current?

I don't see any info in what appears to be the relevant document:
http://direct.xilinx.com/bvdocs/appnotes/xapp382.pdf


Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Back to top
Uwe Bonnes
Posted: Sun Feb 25, 2007 12:30 pm
Guest
Spehro Pefhany <speffSNIP@interlogdotyou.knowwhat> wrote:
Quote:
Hi, all:-

A bit of a long shot here, but does anyone know whether the inputs
will float on the Xilinx CPLD parts will float when power is not
applied or do they have a nasty protection structure to a supply pin?

And if so, what if I float the related Vccio pin-- will that allow the
input current to be reduced to just leakage current?

I don't see any info in what appears to be the relevant document:
http://direct.xilinx.com/bvdocs/appnotes/xapp382.pdf

Some more words are said in the datasheet ds090.pdf, page 11,
Power-Up Characteristics

For the protection structure, perhaps check with an ohmmeter/conduction
tester on an unpowered board...

--
Uwe Bonnes bon@elektron.ikp.physik.tu-darmstadt.de

Institut fuer Kernphysik Schlossgartenstrasse 9 64289 Darmstadt
--------- Tel. 06151 162516 -------- Fax. 06151 164321 ----------
Back to top
Ken Smith
Posted: Sun Feb 25, 2007 5:13 pm
Guest
In article <95e3u21nmibvdcp9nbe9smshjoshbs8186@4ax.com>,
Spehro Pefhany <speffSNIP@interlogDOTyou.knowwhat> wrote:
Quote:
Hi, all:-

A bit of a long shot here, but does anyone know whether the inputs
will float on the Xilinx CPLD parts will float when power is not
applied or do they have a nasty protection structure to a supply pin?

And if so, what if I float the related Vccio pin-- will that allow the
input current to be reduced to just leakage current?

I don't see any info in what appears to be the relevant document:
http://direct.xilinx.com/bvdocs/appnotes/xapp382.pdf

I can't say for sure about the 3.3V version of the Coolrunner but I do
know that there was no diode to the Vdd rail on the 5V parts. They seemed
to have zener/thick-oxide like protection. The input didn't hit a hard
limit as it passed Vcc+0.7 as a diode would. This doesn't mean your idea
will work however. The input leakage current may rise quite a bit before
the hard limit is hit.



--
--
kensmith@rahul.net forging knowledge
Back to top
Spehro Pefhany
Posted: Sun Feb 25, 2007 6:31 pm
Guest
On Sun, 25 Feb 2007 21:52:26 +0000 (UTC), the renowned Uwe Bonnes
<bon@hertz.ikp.physik.tu-darmstadt.de> wrote:

Quote:
Spehro Pefhany <speffSNIP@interlogdotyou.knowwhat> wrote:
Hi, all:-

A bit of a long shot here, but does anyone know whether the inputs
will float on the Xilinx CPLD parts will float when power is not
applied or do they have a nasty protection structure to a supply pin?

And if so, what if I float the related Vccio pin-- will that allow the
input current to be reduced to just leakage current?

I don't see any info in what appears to be the relevant document:
http://direct.xilinx.com/bvdocs/appnotes/xapp382.pdf

Some more words are said in the datasheet ds090.pdf, page 11,
Power-Up Characteristics

For the protection structure, perhaps check with an ohmmeter/conduction
tester on an unpowered board...

Thanks.

I would in a NY minute, if I had one..


Best regards,
Spehro Pefhany
--
"it's the network..." "The Journey is the reward"
speff@interlog.com Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Back to top
 
Page 1 of 1       All times are GMT - 5 Hours
The time now is Tue Dec 02, 2008 12:19 am
Science Forum Index

Powered by phpBB & ML | Disclaimer



Contact Us