| Science Forum Index » Engineering - Lighting Forum » Lights that can be lowered and raised... |
|
Page 2 of 3 Goto page Previous 1, 2, 3 Next |
|
| Author |
Message |
| Richard Crowley... |
 Posted: Mon Oct 26, 2009 6:53 pm |
|
|
|
Guest
|
"Duncan Wood"wrote ...
[quote]Amusingly doing either tends to get the job failed over here, if it's
going to be used for lifting then it gets a barrel clamp & an eye or wedge
socket on the end of the rope.
[/quote]
I did an annual gig where I flew a microphone in the middle of a
60ft span (a giant wood-truss WW2-era quonset hut used as the
gymnasium at the elementary school in Canon Beach, Oregon)
I used 3/16" aircraft cable looped around the entire wood truss,
and secured with three wire clamps at each end. Never had any
problems in 15 years. But I did learn along the way to never trust
anyone else to secure the cable properly. |
|
|
| Back to top |
|
|
|
| Duncan Wood... |
| Posted: Mon Oct 26, 2009 7:02 pm |
|
|
|
Guest
|
On Tue, 27 Oct 2009 00:53:03 -0000, Richard Crowley <rcrowley at (no spam) xp7rt.net>
wrote:
[quote]"Duncan Wood"wrote ...
Amusingly doing either tends to get the job failed over here, if it's
going to be used for lifting then it gets a barrel clamp & an eye or
wedge
socket on the end of the rope.
I did an annual gig where I flew a microphone in the middle of a
60ft span (a giant wood-truss WW2-era quonset hut used as the
gymnasium at the elementary school in Canon Beach, Oregon)
I used 3/16" aircraft cable looped around the entire wood truss,
and secured with three wire clamps at each end. Never had any
problems in 15 years. But I did learn along the way to never trust
anyone else to secure the cable properly.
[/quote]
When you've got a 20000:1 safety margin I'll cut you some slack:-) |
|
|
| Back to top |
|
|
|
| David McCall... |
| Posted: Mon Oct 26, 2009 10:11 pm |
|
|
|
Guest
|
"Richard Crowley" <rcrowley at (no spam) xp7rt.net> wrote in message
news:7kmujgF39dacqU1 at (no spam) mid.individual.net...
[quote]"Duncan Wood"wrote ...
Amusingly doing either tends to get the job failed over here, if it's
going to be used for lifting then it gets a barrel clamp & an eye or
wedge socket on the end of the rope.
I did an annual gig where I flew a microphone in the middle of a
60ft span (a giant wood-truss WW2-era quonset hut used as the
gymnasium at the elementary school in Canon Beach, Oregon)
I used 3/16" aircraft cable looped around the entire wood truss,
and secured with three wire clamps at each end. Never had any
problems in 15 years. But I did learn along the way to never trust
anyone else to secure the cable properly.
That is my point. You know what you can get away with if you do the[/quote]
work yourself, but you don't know how someone else will do it. We
grew up in a time when there was a lot less regulation than there is now.
You hopefully learned some common sense and figured out ways to
accomplish stuff just based on your experience, and what was on hand.
Too many stupid people did dumb stuff and got people hurt in the
process. Now there is an "legally accepted" way to do everything, and
you have to do it that way. It's one of the reasons we look forward to
retirement. Maybe someday after I'm totally useless.
David |
|
|
| Back to top |
|
|
|
| TimR... |
| Posted: Tue Oct 27, 2009 12:54 am |
|
|
|
Guest
|
| How about a long piece of Allthread and a crank? |
|
|
| Back to top |
|
|
|
| RickR... |
| Posted: Tue Oct 27, 2009 4:57 am |
|
|
|
Guest
|
On Oct 27, 3:54 am, TimR <timothy... at (no spam) aol.com> wrote:
[quote]How about a long piece of Allthread and a crank?
[/quote]
There are winches designed for commercial & residential ceilings.
Their purpose is to lower chandeliers for cleaning & re-lamping. I
posted about them in SEL but it didn't cross over.
UL and professional!
---
RickR |
|
|
| Back to top |
|
|
|
| Andrew Gabriel... |
| Posted: Tue Oct 27, 2009 9:29 am |
|
|
|
Guest
|
In article <35028d24-669a-4ce9-95ba-f1e173af4310 at (no spam) a39g2000pre.googlegroups.com>,
RickR <luminousviews at (no spam) gmail.com> writes:
[quote]On Oct 27, 3:54 am, TimR <timothy... at (no spam) aol.com> wrote:
How about a long piece of Allthread and a crank?
There are winches designed for commercial & residential ceilings.
Their purpose is to lower chandeliers for cleaning & re-lamping. I
posted about them in SEL but it didn't cross over.
UL and professional!
[/quote]
This is how to take an expensive chandelier down for cleaning...
http://www.youtube.com/watch?v=7Mf58Yndjsw
--
Andrew Gabriel
[email address is not usable -- followup in the newsgroup] |
|
|
| Back to top |
|
|
|
| Duncan Wood... |
| Posted: Tue Oct 27, 2009 6:48 pm |
|
|
|
Guest
|
On Tue, 27 Oct 2009 19:29:20 -0000, Andrew Gabriel
<andrew at (no spam) cucumber.demon.co.uk> wrote:
[quote]In article
35028d24-669a-4ce9-95ba-f1e173af4310 at (no spam) a39g2000pre.googlegroups.com>,
RickR <luminousviews at (no spam) gmail.com> writes:
On Oct 27, 3:54 am, TimR <timothy... at (no spam) aol.com> wrote:
How about a long piece of Allthread and a crank?
There are winches designed for commercial & residential ceilings.
Their purpose is to lower chandeliers for cleaning & re-lamping. I
posted about them in SEL but it didn't cross over.
UL and professional!
This is how to take an expensive chandelier down for cleaning...
http://www.youtube.com/watch?v=7Mf58Yndjsw
[/quote]
I'm wondering if anyone in the UK didn't think "Brace yourself Rodney"
before going to that clip. |
|
|
| Back to top |
|
|
|
| Lloydj... |
| Posted: Wed Oct 28, 2009 3:34 pm |
|
|
|
Guest
|
[quote] If you really do need the lights to be moved, chain winches can be had
at auto parts or surplus places. Be sure to get chains long enough to
span the vertical distance. Chain winches meant for car engine
replacements come with only a metre or two of lift height.
A cheaper solution is to rig boat winches. They use cable instead of
chain. Attach them to close-by walls and run their cables to the beams via
secondary pulleys.
In all cases, hook the chain or cable to pipe with eyebolts or to
truss. Cheap truss can be had from used TV or amateur radio antenna tower..
--
Richard Bonnerhttp://AIEL.chebucto.biz[/quote] |
|
|
| Back to top |
|
|
|
| Lloydj... |
| Posted: Wed Oct 28, 2009 3:54 pm |
|
|
|
Guest
|
On Oct 23, 8:43 pm, a... at (no spam) chebucto.ns.ca (Atlantic Illumination
Entertainment Lighting) wrote:
[quote]"Jim" <jfer... at (no spam) gmail.com> wrote: in message
We have a high ceiling with large beams. We would like some lighting
that can be raised up next to the beams and then lowered for area
lighting when needed. Anyone seen something that may work for us?
JF
*** Does it actually need to be raised and lowered? If you just need
area light, could you not arrange for the lights to cover the required
area from the beam height?
If you really do need the lights to be moved, chain winches can be had
at auto parts or surplus places. Be sure to get chains long enough to
span the vertical distance. Chain winches meant for car engine
replacements come with only a metre or two of lift height.
A cheaper solution is to rig boat winches. They use cable instead of
chain. Attach them to close-by walls and run their cables to the beams via
secondary pulleys.
In all cases, hook the chain or cable to pipe with eyebolts or to
truss. Cheap truss can be had from used TV or amateur radio antenna tower..
--
Richard Bonnerhttp://AIEL.chebucto.biz
[/quote]
I'm afraid I couldn't disagree with this approach more strongly.
Sounds like the lights are over people's heads (not actors) and MUST
be rigged with properly safety-rated equipment. It could be as simple
as a piece of 1-1/2" sched. 40 black pipe with properly sized wire
rope running through sheaves expressly designed for this purpose,
mounted with an engineered solution to prevent their coming loose, and
then going to a manual or motorized approved winch.
Antenna truss is completely inappropriate for lighting use because the
tubing is typically only about 1" in diameter and it is engineered to
be standing vertically, not hanging horizontally. I have done this
ONLY once to hang commando cloth backdrops because it truly is cheap
stuff.
If you have a budget, look at IFF Manfrotto yo-yo lilts with built-in
electric circuits and are rated for 250kg. They also have to be
mounted properly but that's the end of your engineering since they are
a complete solution. I put about 40 of these things in Sony Music
Studios in Manhattan and they have worked flawlessly.
For all your rigging needs, and maybe a little advice, check with Fehr
Brothers (see them online). They are a wonderful one stop rigging
source.
Anyone who does any rigging these days is under a pall because of a
couple of unfortunate accidents in the recent past. Please don't add
to that poor reputation by using non-rated Home Depot bolts, auto
cable winches (which are 12V DC and consume a huge amount of current),
or other "cheap" solutions and having an accident.
Be smart, and always safety first!
LJ |
|
|
| Back to top |
|
|
|
| Atlantic Illumination Entertainment Lighting... |
| Posted: Thu Oct 29, 2009 2:50 pm |
|
|
|
Guest
|
David McCall wrote:
[quote]"Atlantic Illumination Entertainment Lighting" <aiel at (no spam) chebucto.ns.ca
wrote:
"Jim" <jferree at (no spam) gmail.com> wrote: in message
We have a high ceiling with large beams. We would like some lighting
that can be raised up next to the beams and then lowered for area
lighting when needed. Anyone seen something that may work for us?
JF
[/quote]
(Snip)
[quote]If you really do need the lights to be moved, chain winches can be had
at auto parts or surplus places.
[/quote]
(Snip)
[quote]A cheaper solution is to rig boat winches. They use cable instead of
chain. Attach them to close-by walls and run their cables to the beams via
secondary pulleys.
In all cases, hook the chain or cable to pipe with eyebolts or to
truss. Cheap truss can be had from used TV or amateur radio antenna tower.
--
Richard Bonner
You have wandered out onto a rather shaky limb. Not that the things you
suggested wouldn't work, but are they safe?
[/quote]
*** That depends on how well they are rigged and how strong the beam
is. Jim was pretty vague as to the circumstances.
[quote]Would you be willing to put your name on them as a professional in
this biz?
[/quote]
*** If I select the equipment and do or oversee the rigging - yes.
[quote]Anytime you rig equipment overhead you have to take safety very
seriously. I don't think boat winches and chain motors purchased
at an auto parts store are load rated for theatrical use.
[/quote]
*** It depends on how heavy the lights and support components are. One
can get different ratings for boat winches and chain hoists. The latter
especially would be suitable because they are meant to lift an engine. The
former are bought to handle a given size boat. Allow enough of a rating
margin and it can do the job.
Now I would not raise a major lighting rig with boat winches, but a
pipe with have a half dozen PARS or fresnels is not a problem. There are
caveats to using certain models, though. Some have no lowering control.
Others have no load locks. I see smaller, similar models used in tripod
stands that are legally on the market and they are rated accordingly.
[quote]It is one thing for you to make decisions based on your extensive personal
experience where you will be installing and standing behind it personally.
However it is a completely different thing to suggest these solutions on a
public newsgroup where you have no idea if the people you are advising
may not have any concept of structures and stress. You have no way to
know how they will mount the winch or pulleys, and you don't know how
much weight will be put on it in the future. You don't know if a kid could
come by and release the winch while people are standing under the bar.
[/quote]
*** All valid points, David, but they can apply to anything suggested
here. Users would have to use correct replacement lamps, mount lights
away from flammables and sprinkler heads, wire connectors properly, use
proper overload protection devices, and keep the public away from
equipment.
I am not dissing your response, but any public forum suggestions have
potential to harm if those using the suggestions have not considered
the consequences if they have not engaged professionals or at
least professional advice at their ends to oversee a given job.
[quote]Even if you were willing to stand behind the installation, it still isn't
legal for you to install uncertified components in a public space.
[/quote]
*** Hmm, I don't believe that's the case here in Canada - or at least
not here in Nova Scotia. As long as a component is certified for the rated
load, it should pass inspection.
Now, radio-tower trussing might be a sticking point, but I can tell
you that some of the lighting trussing I have seen in stores and displays
in public places is actually less strong than radio-tower antenna. It's
pretty light duty.
--
Richard Bonner
http://AIEL.chebucto.biz |
|
|
| Back to top |
|
|
|
| Atlantic Illumination Entertainment Lighting... |
| Posted: Thu Oct 29, 2009 2:56 pm |
|
|
|
Guest
|
Duncan Wood wrote:
[quote]On Sat, 24 Oct 2009 16:35:41 +0100, David McCall wrote:
I don't think boat winches and chain motors purchased at an auto
parts store are load rated for theatrical use.
Or any other application where they suspend loads above people.
[/quote]
*** Chain hoists would be rated for that because they do suspend loads
above people - at a minimum, the workers using them.
[quote]Thereagain most chainhoists used in theatre & rock & roll aren't
individually rated to lift or /suspend/ loads above people.
[/quote]
*** Unless some governing body tests them and comes up with a rule
book, those ratings won't appear, either. In the meantime, I'd say that
they fall under industrial usage and so those rules would apply.
--
Richard Bonner
http://AIEL.chebucto.biz |
|
|
| Back to top |
|
|
|
| Atlantic Illumination Entertainment Lighting... |
| Posted: Thu Oct 29, 2009 2:57 pm |
|
|
|
Guest
|
Richard Crowley wrote:
[quote]Local jurisdictions regulate what can be deployed in public
places, whether mechanical or electrical, etc.
[/quote]
*** They sure do and they vary widely, in my experience, as does
enforcement.
[quote]But your warning is a prudent reminder.
[/quote]
*** Agreed.
--
Richard Bonner
http://AIEL.chebucto.biz |
|
|
| Back to top |
|
|
|
| Atlantic Illumination Entertainment Lighting... |
| Posted: Thu Oct 29, 2009 3:04 pm |
|
|
|
Guest
|
David McCall wrote:
[quote]"Richard Crowley" <rcrowley at (no spam) xp7rt.net> wrote:
David McCall wrote:
Even if you were willing to stand behind the installation, it still
isn't legal for you to install uncertified components in a public space.
That is all very true. Note however, that absent direct information,
the original issue does NOT appear to be a theatrical (or even
public for all we know) situation. Remember that this thread was
only cross-posted to r.a.t.s (presumably from s.e.l) after it started.
(Snip)[/quote]
[quote]My warning was more aimed at the idea of advising a total stranger to
use a winch designed for pulling a boat onto a trailer for overhead rigging.
Odds are that it would not be legal and if there was an accident, that
person might point back to this group and say that someone here
suggested that it would be OK.
[/quote]
*** True, but the liability lies with the implementer in the end. A
newsgroup partipant who is perhaps a country or continent away cannot
oversee another participant in his local area who decides to not follow
safety guidelines.
[quote]I'm not paranoid, it's just that everyone IS out to get me :-)
David
[/quote]
*** Lock up your winches then! (-:
--
Richard Bonner
http://AIEL.chebucto.biz |
|
|
| Back to top |
|
|
|
| Atlantic Illumination Entertainment Lighting... |
| Posted: Thu Oct 29, 2009 3:31 pm |
|
|
|
Guest
|
David McCall wrote:
[quote]I really didn't intend to start a rag fest on Richard.
[/quote]
*** I didn't take it that way. It's a discussion group and participants
need not agree with one another. Followups of a dissenting or clarifying
manner, if kept civil, are for the positive.
[quote]He is a very useful member of this community.
[/quote]
*** Thanks, I appreciate that.
[quote]It just seemed like a bad idea to suggest such things in a public
forum where you don't know who you might be influencing.
[/quote]
*** I don't disagree, but as with any suggestions, the user must in the
end decide upon the suitability of those given.
[quote]You might get away with such a winch if you mounted everything
securely and safetyed it once it was in place so that you never
relied on the winch to hold any load except for while it was moving,
and then you took it out before somebody got hurt. Even then it
qualifies as bad practice.
[/quote]
*** Again, I am not saying that boat winches are the answer for every
lighting job, but if a correct winch is bought and is adequately
safeguarded, it may be suitable for some jobs. Certainly, safety chaining
the load in place is a good idea as is guarding the winch itself.
This discussion reminds me of years ago being in some university or
military hall where winches had been used to raise pipes with flags or
some sort of banners (or maybe they were chandeliers) high above the
floor. The winches were accessible to the public, but the handles had been
removed. I don't remember noticing if there were locks on them or not.
[quote]I wouldn't use an eye-bolt here either because the nut has the potential
of working it's way off and dropping its load. So to speak.
[/quote]
*** We rent pipe and chain to a few local theatre groups for one-off
shows every year where the only option is to dead hang. The nuts have
split lockwashers and the eyebolt ends have been peened over the nuts to
prevent exactly that. Also, the longer pipes have three eyebolts.
[quote]I would prefer to wrap the cable around the pipe or perhaps use a
hitch and then swag it or use 3 wire clips to secure it. Faster and
Safer. Pipe isn't much fun to drill anyway.
David
[/quote]
*** We used a v-shaped rest for the pipe and a drill press to keep the
pipe and drill bit straight. A vari-speed pulley system on the drill ran
it at a slow enough speed to bite without skating.
--
Richard Bonner
http://AIEL.chebucto.biz |
|
|
| Back to top |
|
|
|
| Duncan Wood... |
| Posted: Thu Oct 29, 2009 9:31 pm |
|
|
|
Guest
|
On Fri, 30 Oct 2009 00:56:32 -0000, Atlantic Illumination Entertainment
Lighting <aiel at (no spam) chebucto.ns.ca> wrote:
[quote]Duncan Wood wrote:
On Sat, 24 Oct 2009 16:35:41 +0100, David McCall wrote:
I don't think boat winches and chain motors purchased at an auto
parts store are load rated for theatrical use.
Or any other application where they suspend loads above people.
*** Chain hoists would be rated for that because they do suspend loads
above people - at a minimum, the workers using them.
[/quote]
You can buy ones that are, nearly all the ones out there aren't. Don't
stand under the load is fairly commonly (less commonly than legally
required or sensible) stated rule fro any industrial lifting equipment.
[quote]
Thereagain most chainhoists used in theatre & rock & roll aren't
individually rated to lift or /suspend/ loads above people.
*** Unless some governing body tests them and comes up with a rule
book, those ratings won't appear, either. In the meantime, I'd say that
they fall under industrial usage and so those rules would apply.
[/quote]
Well CM say don't. I've never seen an industrial rule that allows standing
under something suspended from a normal lifting machine. |
|
|
| Back to top |
|
|
|
|
