 |
|
| Linux Forum Index » Linux Hardware » Can MB sensor data be read from an ICH10?... |
|
Page 1 of 1 |
|
| Author |
Message |
| ShadowTek... |
 Posted: Thu Oct 15, 2009 5:34 pm |
|
|
|
Guest
|
I just bought a GIGABYTE GA-EP43-UD3L motherboard, which has an Intel P43
and an ICH10, and I can't seem to get *any* MB sensor readings at all, no
temps, voltages, or fan-speeds.
I used to use sensors-applet, which used lm-sensors, but they don't seem
to support the ICH10.
Is there *any* way to get sensor readings from the ICH10 on Linux?
If so, I would like to plug it into a panel applet of some sort, as I
had it before. |
|
|
| Back to top |
|
|
|
| General Schvantzkoph... |
| Posted: Fri Oct 16, 2009 9:12 am |
|
|
|
Guest
|
On Fri, 16 Oct 2009 03:34:57 +0000, ShadowTek wrote:
Quote: I just bought a GIGABYTE GA-EP43-UD3L motherboard, which has an Intel
P43 and an ICH10, and I can't seem to get *any* MB sensor readings at
all, no temps, voltages, or fan-speeds.
I used to use sensors-applet, which used lm-sensors, but they don't seem
to support the ICH10.
Is there *any* way to get sensor readings from the ICH10 on Linux?
If so, I would like to plug it into a panel applet of some sort, as I
had it before.
Have you run sensors-detect? |
|
|
| Back to top |
|
|
|
| ShadowTek... |
| Posted: Fri Oct 16, 2009 11:40 am |
|
|
|
Guest
|
On 2009-10-16, General Schvantzkoph <schvantzkoph at (no spam) yahoo.com> wrote:
Quote:
Have you run sensors-detect?
That found it. Thanks!
It added it87 and coretemp to /etc/modules .
My temp and fan-speed reading look proper, but my voltage readings don't
seem to be complete. There are now entries for "in0" throught "in8",
but the voltage readings are:
1.07
2.13
3.34
2.98
0.06
0.00
0.10
3.09
3.15
I'm assuming that the value multiplier needs to be set?
Would it likely be the same multiplier for every voltage sensor? |
|
|
| Back to top |
|
|
|
| General Schvantzkoph... |
| Posted: Fri Oct 16, 2009 3:51 pm |
|
|
|
Guest
|
On Fri, 16 Oct 2009 21:40:18 +0000, ShadowTek wrote:
Quote: On 2009-10-16, General Schvantzkoph <schvantzkoph at (no spam) yahoo.com> wrote:
Have you run sensors-detect?
That found it. Thanks!
It added it87 and coretemp to /etc/modules .
My temp and fan-speed reading look proper, but my voltage readings don't
seem to be complete. There are now entries for "in0" throught "in8", but
the voltage readings are:
1.07
2.13
3.34
2.98
0.06
0.00
0.10
3.09
3.15
I'm assuming that the value multiplier needs to be set?
Would it likely be the same multiplier for every voltage sensor?
Those things are board dependent. |
|
|
| Back to top |
|
|
|
|
|
All times are GMT - 5 Hours
The time now is Fri Nov 27, 2009 8:39 pm
|
|