| Computers Forum Index » Computer - DCOM - Cisco » Extension cable for Wi-Fi antennas ?... |
|
Page 1 of 1 |
|
| Author |
Message |
| JF Mezei... |
 Posted: Wed Oct 28, 2009 1:15 pm |
|
|
|
Guest
|
I have a 871W router. The 2 antennas are in the back of the unit.
I would like to put the unit in a rack. Would making cables (about 1 or
2metres (3 to 6 feet) to relocate the antennas to the top of the rack
work or would that significantly reduce the power/sensitivity of antennas ?
What type of coax cable would be needed ? |
|
|
| Back to top |
|
|
|
| Doug McIntyre... |
| Posted: Wed Oct 28, 2009 6:54 pm |
|
|
|
Guest
|
JF Mezei <jfmezei.spamnot at (no spam) vaxination.ca> writes:
Quote: I have a 871W router. The 2 antennas are in the back of the unit.
I would like to put the unit in a rack. Would making cables (about 1 or
2metres (3 to 6 feet) to relocate the antennas to the top of the rack
work or would that significantly reduce the power/sensitivity of antennas ?
What type of coax cable would be needed ?
I don't think moving the stock rubber-ducky antennas are going to do
much for range or sensativity. But the reason they are on connectors
is so that you can use your own antennas if you wish.
You can buy many different higher-gain WiFi antennas, all would come
with the proper RP-TNC connectors on them (otherwise, the answer to
your last question is an RP-TNC extension cable).
But if you are worried about range and sensitivity, I'd just go ahead
and swap the rubber-duckys out with something external with a bit more
gain anyway.
Cisco has a huge range they (re)sell...
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.html
But other brands/sources can be cheaper.
Just be careful of connector type, alot of the lower end consumer
stuff switched to a smaller connector (RP-SMA), cisco stuck with the
standard RP-TNC, although some bigger/outdoor antennas may have N, but
cables that go from N to RP-TNC are readily available. (confused yet?) |
|
|
| Back to top |
|
|
|
| Uli Link... |
| Posted: Wed Oct 28, 2009 7:22 pm |
|
|
|
Guest
|
JF Mezei schrieb:
Quote: I have a 871W router. The 2 antennas are in the back of the unit.
I would like to put the unit in a rack. Would making cables (about 1 or
2metres (3 to 6 feet) to relocate the antennas to the top of the rack
work or would that significantly reduce the power/sensitivity of antennas ?
Depends on quality of connectors and cable.
2 meters incl. 2 additional connectors RP-TNC male/female will result in
more than 2dB loss. This may be overcompensated by the better
positioning of the antennas. The cable loss can be significantly higher.
Rule of thumb: the thinner and more flexible the cable is, the higher
the loss per length.
Flexible low loss cable is quite expensive in small quantities.
Quote: What type of coax cable would be needed ?
I strongly recommends buying ready to use cables from professional dealers.
You cannot use your soldering iron. The cable must fit physically into
the connector for matching the impedance.
Your signal uses 2.4 GHz not DC, forget about such things for 5GHz
802.11a radios.
I would place the 870 just on top of the rack as it is no 19" rack unit.
--
ULi |
|
|
| Back to top |
|
|
|
| Rob... |
| Posted: Wed Oct 28, 2009 9:24 pm |
|
|
|
Guest
|
Doug McIntyre <merlyn at (no spam) geeks.org> wrote:
Quote: You can buy many different higher-gain WiFi antennas,
Remember that gain in antennas is always achieved by directivity.
An antenna with higher gain always has more directivity. When the
purpose of the WiFi router is to provide wireless access inside a
building, this may not be what you want. With a suitable pattern
it could be usable for access from a single floor, but that is about it.
Antennas with gain are mainly suitable for point-to-point links. |
|
|
| Back to top |
|
|
|
| Uli Link... |
| Posted: Wed Oct 28, 2009 9:45 pm |
|
|
|
Guest
|
Rob schrieb:
Quote: Doug McIntyre <merlyn at (no spam) geeks.org> wrote:
You can buy many different higher-gain WiFi antennas,
Remember that gain in antennas is always achieved by directivity.
An antenna with higher gain always has more directivity. When the
purpose of the WiFi router is to provide wireless access inside a
building, this may not be what you want. With a suitable pattern
it could be usable for access from a single floor, but that is about it.
Antennas with gain are mainly suitable for point-to-point links.
There are omni directional antennas with 7dB or more gain.
Those direct vertically, but horizontally 360°. Usually an ideal
solution for a single floor.
--
ULi |
|
|
| Back to top |
|
|
|
|
