| Computers Forum Index » Computer Architecture - FPGA » Data2MEM Error - 33 : Matching ADDRESS_SPACE not found... |
|
Page 1 of 1 |
|
| Author |
Message |
| gentel... |
 Posted: Wed Nov 04, 2009 4:42 pm |
|
|
|
Guest
|
hi,all
I am trying to target the XUP by Digilent with my big application. My
settings are almost there, but for some reason I get the following output:
...
Address Map for Processor microblaze
(0x0000000-0x5fffffff) DDR_256MB_64Mx64_rank2_row13_col10_cl2_5 sopb
(0x0000000-0x000ffff) dlmb_cntrl slmb
(0x0000000-0x000ffff) ilmb_cntrl slmb
(0x40600000-0x4060ffff) RS232_Uart_1 sopb
(0x41400000-0x4140ffff) debug module sopb
ERROR:Data2MEM:33 - Matching ADDRESS_SPACE for code segment #4 not found
in 'sys
tem_stub_bd.bmm'.
Code segment #4 occupies [0x50000000:0x5002B357]
thanks for your help..
---------------------------------------
This message was sent using the comp.arch.fpga web interface on
http://www.FPGARelated.com |
|
|
| Back to top |
|
|
|
| Brian Drummond... |
| Posted: Thu Nov 05, 2009 4:53 am |
|
|
|
Guest
|
On Wed, 04 Nov 2009 05:42:30 -0600, "gentel" <gentel86 at (no spam) 163.com> wrote:
Quote: hi,all
I am trying to target the XUP by Digilent with my big application. My
settings are almost there, but for some reason I get the following output:
..
Address Map for Processor microblaze
(0x0000000-0x5fffffff) DDR_256MB_64Mx64_rank2_row13_col10_cl2_5 sopb
(0x0000000-0x000ffff) dlmb_cntrl slmb
(0x0000000-0x000ffff) ilmb_cntrl slmb
(0x40600000-0x4060ffff) RS232_Uart_1 sopb
(0x41400000-0x4140ffff) debug module sopb
ERROR:Data2MEM:33 - Matching ADDRESS_SPACE for code segment #4 not found
in 'sys
tem_stub_bd.bmm'.
Code segment #4 occupies [0x50000000:0x5002B357]
thanks for your help..
At least three problems here:
(1) you have mapped 1.5GB of address space onto 256MB of DDR memory. That'll
work but may not do what you want.
(2) Some of that space is also mapped onto peripherals. Reading from those
regions will definitely not work.
(3) DATA2MEM inserts data into the bitfile used to configure the FPGA. It
follows that the memory being configured must be internal to the FPGA. Yet
according to the address map it is mapped into the DDR module..
- Brian |
|
|
| Back to top |
|
|
|
| gentel... |
| Posted: Thu Nov 05, 2009 6:14 am |
|
|
|
Guest
|
Quote: On Wed, 04 Nov 2009 05:42:30 -0600, "gentel" <gentel86 at (no spam) 163.com> wrote:
thanks for your reply,i got something wrong. the DDR memmory is
(0x50000000-0x5fffffff).but,what should i do if i put the software and
hardware bits into the board????
Quote: hi,all
I am trying to target the XUP by Digilent with my big application. My
settings are almost there, but for some reason I get the following
output:
..
Address Map for Processor microblaze
(0x0000000-0x5fffffff) DDR_256MB_64Mx64_rank2_row13_col10_cl2_5
sopb
(0x0000000-0x000ffff) dlmb_cntrl slmb
(0x0000000-0x000ffff) ilmb_cntrl slmb
(0x40600000-0x4060ffff) RS232_Uart_1 sopb
(0x41400000-0x4140ffff) debug module sopb
ERROR:Data2MEM:33 - Matching ADDRESS_SPACE for code segment #4 not
found
in 'sys
tem_stub_bd.bmm'.
Code segment #4 occupies [0x50000000:0x5002B357]
thanks for your help..
At least three problems here:
(1) you have mapped 1.5GB of address space onto 256MB of DDR memory.
That'll
work but may not do what you want.
(2) Some of that space is also mapped onto peripherals. Reading from
those
regions will definitely not work.
(3) DATA2MEM inserts data into the bitfile used to configure the FPGA. It
follows that the memory being configured must be internal to the FPGA.
Yet
according to the address map it is mapped into the DDR module..
- Brian
---------------------------------------
This message was sent using the comp.arch.fpga web interface on
http://www.FPGARelated.com |
|
|
| Back to top |
|
|
|
| Brian Drummond... |
| Posted: Thu Nov 05, 2009 4:41 pm |
|
|
|
Guest
|
On Wed, 04 Nov 2009 19:14:12 -0600, "gentel" <gentel86 at (no spam) 163.com> wrote:
Quote: On Wed, 04 Nov 2009 05:42:30 -0600, "gentel" <gentel86 at (no spam) 163.com> wrote:
thanks for your reply,i got something wrong. the DDR memmory is
(0x50000000-0x5fffffff).but,what should i do if i put the software and
hardware bits into the board????
what do you mean by putting bits into the board?
If you mean loading the DDR memory with this code segment after power-up, the
usual approach is to write a bootstrap loader - which has to be mapped into
internal memory - which loads this segment from non-volatile storage (e.g. flash
memory, or possibly Ethernet or even the UART.
Alternatively, map this entire segment into internal memory, if there is enough
memory. Or re-write it to use less space.
- Brian |
|
|
| Back to top |
|
|
|
|
